Decontamination

Contents - 500ml

Features

pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.

Directions

1. Wash off sand, mud or dust prior to spraying.

2. Shake bottle well approx. 20 times, and turn trigger "ON".

3. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.

4. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.

* When spray over brake disc, it reacts and changes colour.

Rinse away immediately, if left on too long, may cause bad effects for brake disc.

5. Wipe off with clean towel.

Carry out brake test with low gear 2-3 times after cleaning.

* This product is formulated for wheel.

If use for car body, carefully rinse off with water afterwards.

Contents - 2x 50g Clay Bar

Features

SMOOTH EGG Clay Bar gently removes iron powders and deposits from glass/ ceramic coatings.

Directions

1. Wash car, removing sand and dust from the body of vehicle.

2. Knead clay bar by hand until it's soft and flat.

3. Gently slide clay bar over wet surface. * Be sure to knead the bar regularly to expose fresh clay.

Note: Always let the clay bar do the work never add pressure on the surface.
Always lubricate with water or shampoo water when using clay bar on surface.

Contents - 300 ml

Features

Replaces IPA wipe down. Essential for surface preparation prior to applying wax or ceramic and glass coating, it will improve the adhesion of the coating to the vehicles surface. The aerosol design allows minimum product usage while spreading to a large area!

✔ Oil, Polish residue and fillers remover
✔ Prep item before applying wax / coating
✔ Replaces IPA wipe down
✔ Improves the adhesion of the surface protective coating
✔ Safe for paint 

Directions

1. Shake bottle well

2. Spray on desired panel and wipe dry with a dry detailing microfiber cloth

3. Expose new clean areas of the towel to avoid smearing the collected wax, oil or compound back onto the vehicle.

Contents - 300g 

Features

Clay bar removes unwanted residue such as iron powder, pitch, tar, bird droppings or dead bugs which cause low gloss and dull on the car. It is more effective to use before polishing, waxing or coating.

Direction

1. Wash car to remove sand or dust.

2. Knead clay bar by hand until it's soft and flat.

3. Rub lightly on car surface and wet area being cleaned.

4. If surface of clay bar gets dirty, refold and continue to use clean surface as needed.

Note: Always let the clay bar do the work never add pressure on the surface.
Always lubricate with water or shampoo water when using clay bar on surface.

Contents - 180 ml + Microfiber towel

Features

Cleaner design for glass/ceramic coating contains only mild cleaning ingredients. Restoring brightness of coated vehicle body. Symptoms such as water spots, small scratches on door knobs can be easily removed!

Directions

1. Wash off dirt, dust or mud, and wipe off water.

2. Shake bottle well.

3. Pour a coin size amount of  liquid onto included towel.

4. Rub towel onto surface one panel at a time on affected areas.

Contents - 10 Sheets

Features

Dead bugs, bird droppings and tree sap can cause damage to car paint. Not with FUKUPIKA Bugs& Droppings Removal, simply just wiping, removes and completely cleans the car's surface. Compared with conventional cleaning wipes, this wipe makes it possible give the car a nice clean surface finish,without leaving behind any white residue. The products does not contain any petroleum solvent, making FUKUPIKA absolutely eco-friendly!

Directions

1. Take out one sheet from package.

2. Do not rub with excessive force. If removing heavy dirt, wipe and allow cleaner to penetrate dirt, then gently wipe area. Results may vary depending on the contamination and adhesion of dirt.

3. When removing mud, sand, and dust, wipe off surface lightly and finish with a cleaner side of wipe.
* If white residue of cleaner remains on surface, wipe off with a clean wet towel.

4. If whole sheet gets dirty or dry, use another sheet.
* Seal package firmly, in order to prevent sheets from drying out.

Contents - 4000ml

Features

pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.

Directions

1. Wash off sand, mud or dust prior to spraying.

2. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.

3. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.

* When spray over brake disc, it reacts and changes colour.

Rinse away immediately, if left on too long, may cause bad effects for brake disc.

4. Wipe off with clean towel.

Carry out brake test with low gear 2-3 times after cleaning.

* This product is formulated for wheel.

If use for car body, carefully rinse off with water afterwards.

Contents - 500ml

Features

With Stain Cleaner Strong Type, all you need to do is spray and wipe it off. The white powder won't remain on the surface and re-wiping is NOT necessary. It chemically breaks down and gets rid of stubborn dirt, which normal car shampoo couldn't do. Abrasive compounds are NOT included, so it won't damage your car paint. The fresh scent of grapefruit gets rid off bad odor during the process.

Direction

* Remove dirt from the car in advance.

1. Shake the bottle well.

2. Turn the nozzle to <ON>, and spray it on the surface.

3. Wipe it off with a dry, clean cloth.

Contents - 100ml

Features

Liquid penetrates effectively between the space of adhesive and bonded surface allowed easy removal of sticky adhesive residues.

Direction

* Cut the end of a nozzle into the desired size. 

1. Shear off the edge of a sticker and spray into gap with a small amount of liquid. Then, using the included spatula rub the sticker until it goes off. 

2. In case any glue residue still remains on the surface, it's best to spray it again and let it soak for a while. Then, using a soft cloth try to rub it off. If the glue residue remains on the surface repeat process until completely removed.