High quality trays for storing and sorting of detailing accessories. The depth of the shelf is 86 mm which allows to store even large dimensions of accessories such as polishing pastes. Robust steel and powder finish guarantee excellent appearance and durability of the material.
Fusso Coat 12 Months Wax is a synthetic paint sealant that creates a protective hydrophobic coat on the car's body. It leaves a very smooth and glossy finish. What is by far the most important is the durability! Up to 12 months of beading and sheeting is the reason why Fusso Coat is taking the detailing world by storm. Available in two tone variations to produce best results depending on your vehicle’s paint colour.
✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water
✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc
✔️ Strong Water Repellency – Super hydrophobic coating allowing water to sheet off easily
✔️ Gloss – Creates a thick clear, transparent, deep gloss and shine layer on your vehicles surface
✔️ Coats up to 40 vehicles!
Directions
* Make sure that your car colour is compatible with product.
1. Wash and decontaminate car surface.
2. Dampen included applicator with water and take a very thin amount of wax onto the included applicator sponge, spread it thinly and evenly onto car surface.
3. After surface gets dry (2-3 min), wipe off with a dry soft clean towel for finish.
* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.
*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’ anddo not wash the car in next 24 hours to allow polymerisation.
pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.
Directions
1. Wash off sand, mud or dust prior to spraying.
2. Shake bottle well approx. 20 times, and turn trigger "ON".
3. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.
4. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.
* When spray over brake disc, it reacts and changes colour.
Rinse away immediately, if left on too long, may cause bad effects for brake disc.
5. Wipe off with clean towel.
Carry out brake test with low gear 2-3 times after cleaning.
* This product is formulated for wheel.
If use for car body, carefully rinse off with water afterwards.
The Kiwami, which translates to Extreme Gloss, is a great product for those who desire perfect balance between glossy finish and protection. Extreme Gloss is very easy producing a strong beading effect. Making your car paint shiny and smooth as silk! Available in two tone variations to produce best results depending on your vehicle’s paint colour.
Directions
* Make sure that your car colour is compatible with product.
1. Wash and decontaminate car surface.
2. Take a moderate amount of wax and spread evenly onto car's body using included sponge.
3. After surface gets dry (5-10 minutes in 20℃), wipe off with a soft clean towel.
* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.
* Drying time may be longer in cold temperature.
*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.
Formulated to coat polycarbonate plastic and glass, such as headlight covers, side visors, tail lamp covers, helmet shields and goggles. Specially designed curved applicator and included microfiber cloth for ease of application. Repels water under air pressure when driving. If you are a motorcycle or race car enthusiast, this product sure is suited for your needs!
Directions
1. Prepare the surfaces by washing and decontaminating.
2. Take off the cap and apply directly with felt applicator.
3. Apply gently ensuring full coverage.
4. Immediately wipe off with included towel.
*No need to wait for drying. Wipe off immediately before liquid gets dry.
OUT OF STOCK - BACKORDER E.T.A. END OF NOVEMBER 2020
Contents - 80ml Bottle, 1 x Pad
Features
Newly formulated triple-abrasive particles easily removes scaly spots which conventional compound cleaners cannot. Removes fluorine and sticky oil-film deposits. Restores car's glass close to original transparency. Special application pad is included.
Directions
1. Remove dust and dirt from glass with water, dry off any water remaining on surface.
2. Shake bottle well.
3. Pour liquid onto white side of included pad, begin to polish surface of glass.
Just spray and wipe to freshen up your vehicle’s bodywork, removing light dust and dirt while applying a highly durable Fusso coating, cleaning and coating in one step! The wax coating is reinforced with fluoro polymers to enhance and extend hydrophobicity for up to 180 days. Perfect for maintaining Fusso Coat. Contents will treat 5 mid-size vehicles.
Directions
* Before applying dirty vehicle, be sure to wash dirt off and dry to avoid scratches.
In cases of staining, use specialised cleaners 'Silicone Off'.
1. Shake well and switch nozzle to ON.
2. Spray surface of vehicle, 1 spray for every 30cm2 area.
3. Without allowing to dry, lightly wipe across the surface with a clean, dry towel.
Refold the towel to expose a fresh surface when wiping becomes difficult.
Solid wax creates a hard coating durable up to 1 month. Enhances tire natural gloss black. Can be used to on tires, convertible leather top, fix scuff marks on exterior bumper and trims.
Directions
1. Remove dirt from tires, convertible leather top or bumper in advance.
2. Take cap off and take out included applicator sponge.
3. Put wax on desired area and apply it thinly.
4. Allow to dry for approximately (5-10 minutes), polish with a soft cloth to get ultimate, beautiful matte finish.
Clay bar removes unwanted residue such as iron powder, pitch, tar, bird droppings or dead bugs which cause low gloss and dull on the car. It is more effective to use before polishing, waxing or coating.
Direction
1. Wash car to remove sand or dust.
2. Knead clay bar by hand until it's soft and flat.
3. Rub lightly on car surface and wet area being cleaned.
4. If surface of clay bar gets dirty, refold and continue to use clean surface as needed.
Note: Always let the clay bar do the work never add pressure on the surface. Always lubricate with water or shampoo water when using clay bar on surface.
SMOOTH EGG Clay Bar gently removes iron powders and deposits from glass/ ceramic coatings.
Directions
1. Wash car, removing sand and dust from the body of vehicle.
2. Knead clay bar by hand until it's soft and flat.
3. Gently slide clay bar over wet surface. * Be sure to knead the bar regularly to expose fresh clay.
Note: Always let the clay bar do the work never add pressure on the surface. Always lubricate with water or shampoo water when using clay bar on surface.
Replaces IPA wipe down. Essential for surface preparation prior to applying wax or ceramic and glass coating, it will improve the adhesion of the coating to the vehicles surface. The aerosol design allows minimum product usage while spreading to a large area!
✔ Oil, Polish residue and fillers remover ✔ Prep item before applying wax / coating ✔ Replaces IPA wipe down ✔ Improves the adhesion of the surface protective coating ✔ Safe for paint
Directions
1. Shake bottle well
2. Spray on desired panel and wipe dry with a dry detailing microfiber cloth
3. Expose new clean areas of the towel to avoid smearing the collected wax, oil or compound back onto the vehicle.
Designed to make cleaning easy for both wide areas and tight spaces, the high quality construction of this wheel-cleaning sponge makes it both flexible and sturdy. Unique cellular construction removes dirt efficiently and ultrafine cut-pile microfibers loosen dirt without clogging. Durable inner sponge and innovative glue-free fixings retain elasticity - a long-lasting tool that maintains performance.
Direction
Before use, rinse dirt and soil from the wheel with water.
1. Soak head in water before use.
If washing with water only, thoroughly wet the wheel before use.
Gel type spray glass cleaner lets you clean the glass easily without any liquid or water droplets leaving residue. The cleaning components are held in the gel, giving time to penetrate dirt and increase the effectiveness of cleaning stubborn dirt, such as bird droppings. Also suitable for use on mirrors, unpainted plastic, and rubber parts.
Directions
1. Turn the spray nozzle to “ON”.
2. Without shaking, spray onto the glass surface from 15 – 20cm away, then immediately wipe around the glass with a clean, dry towel.
3. Wipe up the dirt, changing to a fresh surface of the towel when necessary.
*If some residue remains on the glass, wipe again with a clean towel.
Contents - Cleaner (120mL) x 1bottle, Brush x 1pc, Cup x 1pc, Gloves x 2pcs
Features
This is acid type wheel cleaner, can dissolve burned iron powder and brake dust which cannot remove by conventional wheel cleaner with easy procedure. Strong acid cleaner dissolves heavy iron powder, which stuck against wheel, without damaged paint surface.
Directions
1. Remove dirt or oil by car shampoo and wipe off throughly.
2. Be sure that wheel is cool and confirm the area where iron powder is accumulated.
3. Take moderate amount of solution into attached cup, and start applying accumulated area with brush.
4. Let sit 10 minutes, buff off with clean towel. In case of difficultly wiping off once, repeat procedure 3 and 4.
* Application is up to 3 times.
5. Afterwards remove residue by rubbing with water.
* If rinsing is not enough, wheel might discolor, blushing and cause stain.
Stain Eraser for Natural Tanned Leather can remove dirt from leather products such as: shoes, bags, belts or jackets. It is as easy as if you were erasing words with an eraser. It does not require you to use water and cleanser, which does not leave any unwanted stains or spots. Includes convenient to carry protection case. If you bring it in your bag, you can use it easily wherever you are and whenever you want.
<Natural Tanned Leather> Abrasive compounds are not included so there is no damage to the leather surface after unwanted residue is removed. The eraser shavings are splatter-proof and are very soft. We recommend you use this product specifically for white leather where dirt is easily visible.
This eraser is shaped with exclusive, extra fine fibers. It gently removes dirt from suede leather or velour which can easily be damaged.
Apply this, and rain will bead up and roll down the glass, cleanly taking with it any other water along the way. Making use of a specially-developed highly-reactive silicone compound, this glass sealant bonds instantly to the surface, meaning there is no need to dry before wiping off.
Directions
Apply only to clean, dry glass.
1. Remove the cap, press the felt applicator onto the glass and gently squeeze the bottle to let out some liquid.
2. Use the felt applicator to rub the liquid all around the glass. Work on a 50 x 50 cm area at a time.
3. Immediately wipe with a clean, dry towel to spread the liquid over the whole surface and wipe off. Move on to the next area.
*Note: avoid wetting for 10 minutes after application.
Just spray on and wipe off to remove dead bugs, tar, and other oily dirt. It really is that so simple! It also creates a temporary anti-fouling coating to prevent adhesion of dirt.
Directions
* Use on a washed and dried vehicle.
1. Spray on the dirty area from a distance of 20-30 cm.
‘The Kiwami’ is a carefully crafted blend of the finest Carnauba wax, reinforced with our latest synthetic polymers. This blend is designed especially to bring a dazzling gloss and sparkle to the paintwork of your silver vehicle for up to 3 months. This is the ultimate wax for gloss. This is ‘The Kiwami’.
Directions
* Make sure that your car colour is compatible with product.
1. Wash and decontaminate car surface.
2. Take a moderate amount of wax and spread evenly onto car's body using included sponge.
3. After surface gets dry (5-10 minutes in 20℃), wipe off with a soft clean towel.
* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.
* Drying time may be longer in cold temperature.
*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.
The name speaks for itself, extremely high gloss finish wax. King of Gloss creates a thick, heavy gloss coating of synthetic resin that coats your car and gives it the great gloss look similar to transparent nail polish. Available in two tone variations to produce best results depending on your vehicle’s paint colour.
Directions
* Make sure that your car colour is compatible with this product.
* Wash and decontaminate car surface.
1. Take a moderate amount of wax and spread evenly onto car's body using included applicator sponge.
2. After surface gets dry (5-10 minutes), wipe off with a soft clean towel.
*We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.
*Drying time may be longer in winter .
*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.
The name speaks for itself, extremely high gloss finish wax. King of Gloss creates a thick, heavy gloss coating of synthetic resin that coats your car and gives it the great gloss look similar to transparent nail polish. Available in two tone variations to produce best results depending on your vehicle’s paint colour.
Directions
* Make sure that your car colour is compatible with this product.
* Wash and decontaminate car surface.
1. Take a moderate amount of wax and spread evenly onto car's body using included applicator sponge.
2. After surface gets dry (5-10 minutes), wipe off with a soft clean towel.
*We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.
*Drying time may be longer in winter .
*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.
Coating agent creates super hydrophobic layer onto wheel surface, prevents brake dust adhesion and keeps beautiful condition for a long time. Nano size lotus leaf coating agent prevents adhering water, brake dust and dramatically repels the dirt. All you have to do is wash the wheels, wipe off water, remove oily component with included wipes, then spray and dry. 8 wheels are available to apply in 1 bottle.
Directions
1. Clean wheels by removing dirt with detergent and dry off water.
2. Use included wipes to decontaminate surface ensure all areas are wiped down.
3. Shake bottle well and spray 10cm away from wheel.
Allow to dry 20min in summer (30℃), 60min in winter (10℃)
Do not drive until it gets dry.
* If, surface gets whiten or liquid streak looks uneven, symptom would disappear after time goes by. (If large amount is sprayed, whiten marks will remain)
* Liquid may accumulate at bottom of tires, in case wipe off with wrung towel before it dries. If liquid adheres to other areas, wipe off immediately.
The super extra fine microfiber cloth with triangular, cross-section patterns demonstrates a tremendous ability to absorb water and drastically reduces wiping time after washing.
Super extra fine microfiber is effective in removing light levels of unwanted residue.
Big size microfiber cloth 300mm x 1000mm allows for quick easy drying.
Forget about water spots! Water Block is a sheeting wax that will make water simply slide down your car paint. Blended carnauba and high-adhesive polymers create a great combination of hydrophobicity and natural shine. Combine this wax with products from the Glaco series to create an ultimate raincoat for your car! Available in two tone variations to produce best results depending on your vehicle’s paint colour.
Directions
* Make sure that your car colour is compatible with product.
* Wash off any sand, dust, and dirt, and wipe off any remaining water drops.
1. Take a moderate amount of the wax and spread it evenly onto car's body using the included sponge.
2. After the surface gets dry (5-10 minutes), wipe off with a soft clean towel.
* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer
Forget about water spots! Water Block is a sheeting wax that will make water simply slide down your car paint. Blended carnauba and high-adhesive polymers create a great combination of hydrophobicity and natural shine. Combine this wax with products from the Glaco series to create an ultimate raincoat for your car! Available in two tone variations to produce best results depending on your vehicle’s paint colour.
Directions
* Make sure that your car color is compatible with product.
* Wash off any sand, dust, and dirt, and wipe off any remaining water drops.
1. Take a moderate amount of the wax and spread it evenly onto car's body using the included sponge.
2. After the surface gets dry (5-10 minutes), wipe off with a soft clean towel.
* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer
A must have product for all detailers and enthusiast to buff off wax or sealants. ‘Wipe Cloth' has low oil absorption leaving the wax and gloss on the surface of the surface of the vehicle and not absorbing into the cloth. Cloth is washable so can be used repeatedly.