SOFT99

Contents - 100ml

Features

Combining the abrasive powder of small, hard particles and big, soft particles, Glaco Glass Compound Roll-On is able to remove the toughest stains made from oily dirt and fluorine film. By just applying the product lightly onto the glass you will see immediate results as the roll-on removes the oil-film with ease. This convenient product can be used as surface preparation just before applying any coating to the glass.

Directions

1. Remove dust and dirt from glass with water, wipe off any water drops remaining on surface.

2. Shake bottle well with cap on and remove plastic seal.

3. Squeeze handle part of bottle to release compound liquid.

4.Polish onto glass until surface stops repelling liquid.

5. Wait for compound to dry, then wash glass clean with water to make a slurry and wipe off.

6. Remove polishing pad from applicator, then wash and dry for future use.

Contents - 70ml

Features

Maintains a strong coating which resists friction from wipers, dust, car-wash or cleansers, and lasts 6 times longer than conventional coating agents. The water repellency lasts up about 1 year.

Directions

1. Remove dust and dirt from windscreen with water.

2. Use ‘Glaco Roll On Compound’ in advance for surface preparation.

3. Take cap off and apply on dry windscreen.

4. Press side of bottle to allow fluid out and rub firmly onto windscreen without splashing fluid.
* Do not apply on wet windscreen as it may cause uneven marks to surface.

5. After drying for 5-10 minutes, wipe off with a dry clean towel.

6. Allow drying for at least 12 hours for coating to bond firmly onto windscreen.

Contents - 200g

Features

Fusso Coat 12 Months Wax is a synthetic paint sealant that creates a protective hydrophobic coat on the car's body. It leaves a very smooth and glossy finish. What is by far the most important is the durability! Up to 12 months of beading and sheeting is the reason why Fusso Coat is taking the detailing world by storm. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water

✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc

✔️ Strong Water Repellency – Super hydrophobic coating allowing water to sheet off easily

✔️ Gloss – Creates a thick clear, transparent, deep gloss and shine layer on your vehicles surface

✔️ Coats up to 40 vehicles!

Directions

* Make sure that your car colour is compatible with product.

1. Wash and decontaminate car surface.

2. Dampen included applicator with water and take a very thin amount of wax onto the included applicator sponge, spread it thinly and evenly onto car surface.

3. After surface gets dry (2-3 min), wipe off with a dry soft clean towel for finish.

* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’ and do not wash the car in next 24 hours to allow polymerisation.

Contents - 40 ml

Features

Repellent prevents water from remaining on the surface by lining the mirror with super-fine, microscopic studs. Spray creates an even coating and shortens the process. Suitable for reverse surfaces such as mirrors and reverse cameras.

Directions

* Clean side mirror/ reverse camera with car shampoo or 'Glaco Compound Roll On'

1. Spray evenly onto surface from a distance of approximately 15cm.
We recommend putting a towel around the mirror while spraying, in order to prevent fluid getting on other parts

2. Allow to dry completely (in the summer for 1 hour, in the winter for 2 hours)

*Do not touch surface when dry.

Contents - 1pc

Features

You can wash wheels as if you were washing with your own hands. The Wheel Mitt helps you wash even the narrowest of spaces on the wheels where a sponge cannot reach. It is designed to prevent water from soaking into your wrist. Can be used for left or right hand.

Contents - Abrasive 80ml, Ultrafine pad L ×1, Ultrafine pad S ×1, Compound Sponge ×1

Features

The high-gloss black plastic known as piano black shows scratches very easily, and can show age much more quickly than paint or other areas of the vehicle. This kit makes it easy to restore painted and unpainted piano black and other high-gloss plastics by hand, refining them to a near new condition.

Direction

Note: Be sure to thoroughly clean and thoroughly dry the area to be treated, and mask off neighbouring areas. Use a scratch removal compound (sold separately) with the compound sponge to remove any deep scratches beforehand.

1. With the cap closed, shake the bottle well.

2. Choose an ultrafine pad size appropriate or comfortable. Apply a moderate amount of compound to the black surface of the pad. Polish the surface while spreading the liquid in horizontal and vertical motions. Aim work on one 30×30 cm area at a time.

3. After polishing, remove any masking and wipe up any residue with a soft, clean towel.

Contents - 110ml

Features

Using the newly developed S.A.R.F. (Strong Adhesion + Rapid Finish) technology, the latest generation of Glaco creates an ultra-smooth layer that pushes away rain more powerfully than ever before... and it lasts for 4 months!
The swivel-head and large, square application felt allow for much easier application and make sure the corners get a proper coat.
Also repels traffic film, snow, and frost!

Directions

*Note: Wash away dirt and dust, and dry completely before application.

           Unscrew the cap and remove.

1. Press onto the glass and gently squeeze to release the liquid, allowing it to soak into the felt head.

2. Apply to the glass in a criss-cross pattern, squeezing to release more liquid as necessary. Leave no gaps.

3. Dry for 5-10 minutes, and wipe up with a tightly-wrung out damp towel.

Incomplete removal may lead to wiper judder.

Contents - 300 ml

Features

Multi-purpose interior cleaner. Can be used on all surface (fabric, trims, dash, and windows. Super quick drying, leaves no additional finish. Eliminates odour and leaves a refreshing grape fruit scent. Contains ethanol for antibacterial clean.

Directions

When cleaning inside window, seat and floor mat:

1. Remove navy stopper behind trigger.

2. Directly spray onto area and wipe off with dry clean towel.
* Allow liquid to soak, then wipe off
* Wipe off with water if use for cleaning child seat.

When cleaning dash board, handles, trims, plastic and LCD screen

1. Removal navy stopper behind trigger.

2. Spray liquid directly onto clean dry towel and wipe desired area.

Features

Contents - 200g

Features

Fusso Coat 12 Months Wax is a synthetic paint sealant that creates a protective hydrophobic coat on the car's body. It leaves a very smooth and glossy finish. What is by far the most important is the durability! Up to 12 months of beading and sheeting is the reason why Fusso Coat is taking the detailing world by storm. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water

✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc

✔️ Strong Water Repellency – Super hydrophobic coating allowing water to sheet off easily

✔️ Gloss – Creates a thick clear, transparent, deep gloss and shine layer on your vehicles surface

✔️ Coats up to 40 vehicles!

Directions

* Make sure that your car colour is compatible with product.

1. Wash and decontaminate car surface.

2. Dampen included applicator with water and take a very thin amount of wax onto the included applicator sponge, spread it thinly and evenly onto car surface.

3. After surface gets dry (2-3 min), wipe off with a dry soft clean towel for finish.

* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’ and do not wash the car in next 24 hours to allow polymerisation.

Contents - 500ml

Features

pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.

Directions

1. Wash off sand, mud or dust prior to spraying.

2. Shake bottle well approx. 20 times, and turn trigger "ON".

3. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.

4. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.

* When spray over brake disc, it reacts and changes colour.

Rinse away immediately, if left on too long, may cause bad effects for brake disc.

5. Wipe off with clean towel.

Carry out brake test with low gear 2-3 times after cleaning.

* This product is formulated for wheel.

If use for car body, carefully rinse off with water afterwards.

Contents - 200g

Features

The Kiwami, which translates to Extreme Gloss, is a great product for those who desire perfect balance between glossy finish and protection. Extreme Gloss is very easy producing a strong beading effect. Making your car paint shiny and smooth as silk! Available in two tone variations to produce best results depending on your vehicle’s paint colour.

Directions

* Make sure that your car colour is compatible with product.

1. Wash and decontaminate car surface.

2. Take a moderate amount of wax and spread evenly onto car's body using included sponge.

3. After surface gets dry (5-10 minutes in 20℃), wipe off with a soft clean towel.

* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

* Drying time may be longer in cold temperature.

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.

Contents - 70 ml

Features

Formulated to coat polycarbonate plastic and glass, such as headlight covers, side visors, tail lamp covers, helmet shields and goggles. Specially designed curved applicator and included microfiber cloth for ease of application. Repels water under air pressure when driving. If you are a motorcycle or race car enthusiast, this product sure is suited for your needs!

Directions

1. Prepare the surfaces by washing and decontaminating.

2. Take off the cap and apply directly with felt applicator.

3. Apply gently ensuring full coverage.

4. Immediately wipe off with included towel.

*No need to wait for drying. Wipe off immediately before liquid gets dry.

Contents - 80ml Bottle, 1 x Pad

Features

Newly formulated triple-abrasive particles easily removes scaly spots which conventional compound cleaners cannot. Removes fluorine and sticky oil-film deposits. Restores car's glass close to original transparency. Special application pad is included.

Directions

1. Remove dust and dirt from glass with water, dry off any water remaining on surface.

2. Shake bottle well.

3. Pour liquid onto white side of included pad, begin to polish surface of glass.

4. Finally, wash glass cleanly with water.

Contents - 1x Coating Agent bottle (15mL), 2x Hard Sponge, 2x Soft Sponge, 3x Silicone off Wipes Sheets, 2x Gloves

Features

Bring the life back to faded plastic and rubber trim! This treatment restores the deep darkness, natural gloss, and rich texture of black trim to revitalize your vehicle. The unique coating liquid penetrates into the surface and polymerizes to form a flexible yet glossy surface, making it suitable for restoring both hard plastic and soft rubber!

Direction

Note: Apply only to clean, dry, unpainted plastic and rubber.

1. First clean and degrease the area to be treated using the included ‘Silicone Off’ degreasing sheets.

Note: Some textured plastics may pick up fibers from the sheet. Remove these before proceeding. To prevent the sheets from drying out, firmly seal the package between uses.

2. Cut sponge to suitable size for area to be treated. The black sponge is for hard plastic, the white sponge is for soft rubber. Apply a small amount of the liquid (green label), and spread thinly and evenly across the surface to be treated.

Note: Some rubber parts may absorb the liquid. Keep applying until enough liquid remains.

3. After drying for around 5 minutes, use a fresh sheet to lightly wipe up the surface for an even finish. If left for too long, the excess will not be possible to remove.

Note: Do not touch or wet for 24 hours. Do not reuse sponges that have hardened. If the liquid unintentionally comes into contact with another surface, wipe off immediately.

Content - 170g

Features

Solid wax creates a hard coating durable up to 1 month. Enhances tire natural gloss black. Can be used to on tires, convertible leather top, fix scuff marks on exterior bumper and trims.

Directions

Contents - 2x 50g Clay Bar

Features

SMOOTH EGG Clay Bar gently removes iron powders and deposits from glass/ ceramic coatings.

Directions

1. Wash car, removing sand and dust from the body of vehicle.

2. Knead clay bar by hand until it's soft and flat.

3. Gently slide clay bar over wet surface. * Be sure to knead the bar regularly to expose fresh clay.

Note: Always let the clay bar do the work never add pressure on the surface.
Always lubricate with water or shampoo water when using clay bar on surface.

Contents - 300 ml

Features

Replaces IPA wipe down. Essential for surface preparation prior to applying wax or ceramic and glass coating, it will improve the adhesion of the coating to the vehicles surface. The aerosol design allows minimum product usage while spreading to a large area!

✔ Oil, Polish residue and fillers remover
✔ Prep item before applying wax / coating
✔ Replaces IPA wipe down
✔ Improves the adhesion of the surface protective coating
✔ Safe for paint 

Directions

1. Shake bottle well

2. Spray on desired panel and wipe dry with a dry detailing microfiber cloth

3. Expose new clean areas of the towel to avoid smearing the collected wax, oil or compound back onto the vehicle.

Contents - 300g 

Features

Clay bar removes unwanted residue such as iron powder, pitch, tar, bird droppings or dead bugs which cause low gloss and dull on the car. It is more effective to use before polishing, waxing or coating.

Direction

1. Wash car to remove sand or dust.

2. Knead clay bar by hand until it's soft and flat.

3. Rub lightly on car surface and wet area being cleaned.

4. If surface of clay bar gets dirty, refold and continue to use clean surface as needed.

Note: Always let the clay bar do the work never add pressure on the surface.
Always lubricate with water or shampoo water when using clay bar on surface.

Contents - 1x Wheel Cleaning Sponge

Features

Designed to make cleaning easy for both wide areas and tight spaces, the high quality construction of this wheel-cleaning sponge makes it both flexible and sturdy. Unique cellular construction removes dirt efficiently and ultrafine cut-pile microfibers loosen dirt without clogging. Durable inner sponge and innovative glue-free fixings retain elasticity - a long-lasting tool that maintains performance.

Direction

Before use, rinse dirt and soil from the wheel with water.

1. Soak head in water before use.

If washing with water only, thoroughly wet the wheel before use.

2. After use, rinse and dry thoroughly.

If dirt remains, wash with pH-neutral detergent.

Contents - 500ml

Features

Gel type spray glass cleaner lets you clean the glass easily without any liquid or water droplets leaving residue. The cleaning components are held in the gel, giving time to penetrate dirt and increase the effectiveness of cleaning stubborn dirt, such as bird droppings. Also suitable for use on mirrors, unpainted plastic, and rubber parts.

Directions

1. Turn the spray nozzle to “ON”.

2. Without shaking, spray onto the glass surface from 15 – 20cm away, then immediately wipe around the glass with a clean, dry towel.

3. Wipe up the dirt, changing to a fresh surface of the towel when necessary.

*If some residue remains on the glass, wipe again with a clean towel.

 Contents - Cleaner (120mL) x 1bottle, Brush x 1pc, Cup x 1pc, Gloves x 2pcs

Features

This is acid type wheel cleaner, can dissolve burned iron powder and brake dust which cannot remove by conventional wheel cleaner with easy procedure.
Strong acid cleaner dissolves heavy iron powder, which stuck against wheel, without damaged paint surface.

Directions

1. Remove dirt or oil by car shampoo and wipe off throughly.

2. Be sure that wheel is cool and confirm the area where iron powder is accumulated.

3. Take moderate amount of solution into attached cup, and start applying accumulated area with brush.

4. Let sit 10 minutes, buff off with clean towel. In case of difficultly wiping off once, repeat procedure 3 and 4.

* Application is up to 3 times.

5. Afterwards remove residue by rubbing with water.

* If rinsing is not enough, wheel might discolor, blushing and cause stain.

Contents - 1pc

Features

Stain Eraser for Natural Tanned Leather can remove dirt from leather products such as: shoes, bags, belts or jackets. It is as easy as if you were erasing words with an eraser. It does not require you to use water and cleanser, which does not leave any unwanted stains or spots. Includes convenient to carry protection case. If you bring it in your bag, you can use it easily wherever you are and whenever you want.

＜Natural Tanned Leather＞
　Abrasive compounds are not included so there is no damage to the leather surface after unwanted residue is removed. The eraser shavings are splatter-proof and are very soft. We recommend you use this product specifically for white leather where dirt is easily visible.

This eraser is shaped with exclusive, extra fine fibers. It gently removes dirt from suede leather or velour which can easily be damaged.

Contents - 75 ml

Features

Apply this, and rain will bead up and roll down the glass, cleanly taking with it any other water along the way. Making use of a specially-developed highly-reactive silicone compound, this glass sealant bonds instantly to the surface, meaning there is no need to dry before wiping off.

Directions

Apply only to clean, dry glass.

1. Remove the cap, press the felt applicator onto the glass and gently squeeze the bottle to let out some liquid.

2. Use the felt applicator to rub the liquid all around the glass. Work on a 50 x 50 cm area at a time.

3. Immediately wipe with a clean, dry towel to spread the liquid over the whole surface and wipe off. Move on to the next area.

*Note: avoid wetting for 10 minutes after application.

Contents - 420 ml

Features

Just spray on and wipe off to remove dead bugs, tar, and other oily dirt. It really is that so simple! It also creates a temporary anti-fouling coating to prevent adhesion of dirt.

Directions

* Use on a washed and dried vehicle.

1. Spray on the dirty area from a distance of 20-30 cm.

2. Wipe off with a dry towel.